Makine Mühendisliği Bölümü Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.11779/1944
Browse
17 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 3Powder metallurgy processing of seven/eight component multi-phase (HfTiZr-Mn/Mo/W/Cr/Ta)B<sub>2</sub> high entropy diboride ceramics(Elsevier, 2024) Suzer, Ilayda; Akbari, Amir; Ates, Semih; Bayrak, Kuebra Gurcan; Mertdinc-Ulkuseven, Siddika; Arisoy, C. Fahir; Agaogullari, Duygu; Öveçoğlu, M. LutfiThis study aims to show the possibility of synthesizing seven- and eight-component high entropy diboride (HEB) ceramics using high energy ball milling-assisted spark plasma sintering (SPS). Metal boride powders, synthesized in laboratory conditions from metal oxide-boron oxide-magnesium powder blends, were combined equimolarly as seven and eight components containing systems. Afterwards, hybridized powders were mechanically alloyed (MA) for 6 h and subjected to spark plasma sintering (SPS) at 2000 degrees C and under 30 MPa. Detailed phase analysis and physical, microstructural, and mechanical characterization of the samples were performed. in the sintered products, the main phase belongs to the HEB, and also low amounts of Hf/Zr oxides and secondary phases (W or Ti-rich) occurred. The highest hardness was observed at the (HfTiZrMoWCrTa)B-2 with 25 GPa, and the lowest hardness was seen at the (HfTiZrMnCrMoWTa)B2 with 17 GPa. Also, the highest wear resistance was calculated for the (HfTiZrMnCrMoTa)B-2 as 6.05 x 10(-7) mm(3)/Nm. Additionally, (HfTiZrMnMoWTa)B-2 and (HfTiZrMnMoCrTa)B-2 have the highest and lowest Archimedes' densities, with 7.94 g/cm(3) and 6.91 g/cm(3), respectively.Article Citation - WoS: 8Citation - Scopus: 10Identification of the Viscoelastic Properties of Soft Materials Using a Convenient Dynamic Indentation System and Procedure(Elsevier, 2022) Körük, Hasan,; Beşli, Ayça,; Koç, Ömer Hayati,; Yurdaer, Berk Salih,; Yurdaer, Salih Berk; Koc, Hayati OmerThe responses of soft structures such as tissue depend on their viscoelastic properties. Therefore, the knowledge of the elastic and damping properties of soft materials is of great interest. This paper presents the identification of the viscoelastic properties of soft materials using a convenient dynamic indentation system and procedure. Using an electromagnet, a force is applied to a rigid sphere located at the soft-material interface and the dynamic response of the sphere is recorded using a high-speed camera. The recorded video is processed to identify the displacement of the sphere as a function of time. The dynamic response of the sphere located at the soft-material interface is predicted using an analytical model that considers the shear modulus and density of the soft sample, the radiation damping due to shear waves, and the radius and density of the sphere. By matching the measured and predicted steady-state displacements of the sphere, the shear modulus of the soft sample is determined. The viscous damping ratio of the soft sample is identified by using an equivalent viscous damping ratio for the soft sample in the analytical model and matching the measured and predicted oscillation amplitudes of the sphere. Experiments and analyzes are performed using gelation phantoms with different mechanical properties, spheres of different materials and sizes, and different force levels to verify the system and procedure. Three experiments are performed for each gelation phantom, sphere, and external force, and the repeatability of the results is presented. The results show that the dynamic indentation system and procedure presented in this study can be conveniently used to determine the viscoelastic properties of soft materials in practical applications.Article Citation - WoS: 34Citation - Scopus: 37Development of a New Solar, Gasification and Fuel Cell Based Integrated Plant(Elsevier, 2021) Dinçer, İbrahim; Karapekmez, ArasDespite its shortcomings, fossil-based fuels are still utilized as the main energy source, accounting for about 80% of the world's total energy supply with about one-third of which comes from coal. However, conventional coal-fired power plants emit relatively higher amounts of greenhouse gases, and the derivatives of air pollutants, which necessitates the integration of environmentally benign technologies into the conventional power plants. In the current study, a H2–CO synthesis gas fueled solid oxide fuel cell (SOFC) is integrated to the coal-fired combined cycle along with a concentrated solar energy system for the purpose of promoting the cleaner energy applications in the fossil fuel-based power plants. The underlying motivation of the present study is to propose a novel design for a conventional coal-fired combined cycle without altering its main infrastructure to make its environmentally hazardous nature more ecofriendly. The proposed SOFC integrated coal-fired combined cycle is modeled thermodynamically for different types of coals, namely pet coke, Powder River Basin (PRB) coal, lignite and anthracite using the Engineering Equation Solver (EES) and the Ebsilon software packages. The current results show that the designed hybrid energy system provide higher performance with higher energy and exergy efficiencies ranging from 70.6% to 72.7% energetically and from 35.5% to 43.8% exergetically. In addition, carbon dioxide emissions are reduced varying between 18.31 kg/s and 30.09 kg/s depending on the selected coal type, under the assumption of 10 kg per second fuel inlet.Article Citation - WoS: 28Citation - Scopus: 29Development of a New Integrated Energy System With Compressed Air and Heat Storage Options(Elsevier, 2020) Javania, Nader; Dinçer, İbrahim; Karapekmez, Aras; Javani, NaderThe present study investigates a biomass driven power plant integrated with compressed air and thermal energy storage subsystems. Compressed air energy storage system exploits the pressurized air at non-peak periods to be used in peak times when there is a need for extra energy. Thermal energy storage systems including phase change material, allow the solar subsystem to operate independently in order to produce hot air when solar irradiation is insufficient. The energy stored in the present system is then supplied to both the gasifier and combustion chamber in order to achieve a higher combustion efficiency. Three different phase change materials (PCMs) are investigated and their efficiencies are comparatively evaluated. Among the considered PCMs, LiNO3 is the most suitable material for the considered system with 82% energy efficiency and 84% exergy efficiency. The current study also aims at designing a renewable energy based power plant which operates continuously through using storage subsystems and is more environmental benign compared to fossil fuel based conventional systems. In this regard, wet wood (CH1.46O0.64N0.002) with 15% moisture content is selected as a fuel instead of fossil-based fuels in order to reduce the greenhouse gas emissions and eliminate the dep endency on fossil fuels. A comprehensive thermodynamic analysis is conducted to evaluate the entropy generations, exergy destructions, and energy and exergy efficiencies. The highest overall energy and exergy efficiencies are obtained as 28.58% and 24.08% in the discharging period, respectively.Article Citation - WoS: 9Citation - Scopus: 11Development of an Equivalent Shell Finite Element for Modelling Damped Multi-Layered Composite Structures(Elsevier, 2020) Şanlıtürk, Kenan Y.; Özer, Mehmet Sait; Körük, HasanA new equivalent shell finite element (FE) for modelling damped multi-layered structures is presented in this study. The method used for developing the new FE for such structures is based on the idea that the strain energy of the equivalent single-layer FE must be equal to the sum of the strain energies of individual layers. The so-called energy coefficients are defined for this purpose for the extensional, bending and shear deformations of the composite structure. These coefficients are then determined and used as correction multipliers during stacking the elemental matrices of individual layers. Two approaches, based on second-order strain or stress distribution assumption through the composite thickness, are investigated for deriving the shear energy coefficients. The damping capability of the FE developed here originates from using complex Young's modulus to define the material properties of individual layers. The resulting equivalent single-layer shell element with four nodes has six degrees-of-freedom per node. The accuracy, advantages and limitations of the composite FE developed in this work are investigated using experimental as well as theoretical results. In the light of the finding of these investigations, further enhancement in the formulation is made by also utilising a new shear correction factor for the individual layers in the equivalent shell element. Final results for free- and constrained-layered structures confirm that the equivalent shell FE developed here can be used effectively for the prediction of the modal properties of damped multi-layered structures.Article Citation - WoS: 14Citation - Scopus: 15Elastic Deformation of Soft Tissue-Mimicking Materials Using a Single Microbubble and Acoustic Radiation Force(Elsevier, 2020) Körük, Hasan; Bezer, James H.; J Rowlands, Christopher; Choi, James J.; Rowlands, Christopher J.Mechanical effects of microbubbles on tissues are central to many emerging ultrasound applications. Here, we investigated the acoustic radiation force a microbubble exerts on tissue at clinically relevant therapeutic ultrasound parameters. Individual microbubbles administered into a wall-less hydrogel channel (diameter: 25–100 µm, Young's modulus: 2–8.7 kPa) were exposed to an acoustic pulse (centre frequency: 1 MHz, pulse length: 10 ms, peak-rarefactional pressures: 0.6–1.0 MPa). Using high-speed microscopy, each microbubble was tracked as it pushed against the hydrogel wall. We found that a single microbubble can transiently deform a soft tissue-mimicking material by several micrometres, producing tissue loading–unloading curves that were similar to those produced using other indentation-based methods. Indentation depths were linked to gel stiffness. Using a mathematical model fitted to the deformation curves, we estimated the radiation force on each bubble (typically tens of nanonewtons) and the viscosity of the gels. These results provide insight into the forces exerted on tissues during ultrasound therapy and indicate a potential source of bio-effects.Article Citation - WoS: 13Citation - Scopus: 13Mechanics of Milling 48-2 Gamma Titanium Aluminide(Elsevier, 2020) Layegen, S. Ehsan; Lazoğlu, İsmail; Hussain, Abbas; Arrazola, Pedro-J.; Subaşı, Ömer; Yavaş, Çağlar; Lazcano, Xabier; Öztürk, Çağlar; Yiğit, İ. Enes; Aristimuno, Patxi-X.; Layegh, S. EhsanAccurate and fast prediction of cutting forces is important in high-performance cutting in the aerospace industry. Gamma titanium aluminide (gamma-TiAl) is a material of choice for aerospace and automotive applications due to its superior thermo-mechanical properties. Nevertheless, it is a difficult to machine material. This article presents the prediction of cutting forces for Ti-48Al-2Cr-2Nb (48-2-2) gamma-TiAl in milling process using orthogonal to oblique transformation technique. The novelty of this paper lies in reporting the orthogonal database of 48-2-2 gamma-TiAl. Fundamental cutting parameters such as shear stress, friction angle and shear angle are calculated based on experimental measurements. Friction coefficients are identified for two different coating conditions which are AlTiN, and AlCrN on carbide tools. Predicted results are validated with the experimental cutting forces during end milling and ball-end milling operations for different cutting conditions. The simulated results showed good agreement with the experimental results, which confirms the validity of the force modelArticle Citation - WoS: 6Citation - Scopus: 7Testing Non-Magnetic Materials Using Oberst Beam Method Utilising Electromagnetic Excitation(Elsevier, 2019) Özer, Mehmet Sait; Körük, Hasan; Şanlıtürk, Kenan YüceThe use of a non-contact electromagnetic excitation system is highly recommended in the literature to identify the mechanical properties of materials using the Oberst Beam Method. However, it is not possible to test a specimen made of non-magnetic material using the Oberst beam test rig, comprising of an electromagnetic exciter, unless the specimen is modified using some magnetic particles or small discs made of a ferromagnetic material. Although doing so makes it possible to perform the test, this results in an undesirable modification to the test specimen, leading to unquantified levels of errors in the estimated material properties. This study proposes an approach for eliminating the adverse effects of such mass modification to the test specimen, and also allows subsequent removal of the electromagnetic stiffening effects produced by the electromagnetic exciter. The proposed method is validated using both finite element (FE) simulations and experimental data. Results confirm that the proposed method for the removal of the adverse effects of mass modification, combined with the subsequent removal of the electromagnetic stiffening effects, is very effective, making it possible to determine the material properties of non-magnetic materials with a very good accuracy.Editorial 17th International Conference on Mechatronics Technology, October 15-18, 2013, Jeju Island, Korea(Elsevier, 2015) Hwang, Sung Ho; Kim, Joon-wan; Dorantes-Gonzalez, Dante JorgeIn recent years, Mechatronics has gained a lot of interest as more applications have been introduced to industry and society. The need for new mechatronic technologies in the form of advanced production systems, mechatronic devices, control systems, robotics, biomedical applications, MEMS, and measurement systems, among others, is very much required in improving productivity and competitiveness in many industries. Thus, this conference was organized to address the state-of-the-art technology for the benefit of researchers and users, and this time the conference made a special focus on the topic: Sustainable Mechatronics Technology.Article Citation - WoS: 13Citation - Scopus: 17Acoustic Streaming in a Soft Tissue Microenvironment(Elsevier, 2019) El Ghamrawy, Ahmed; Mohammed, Ali; Jones, Julian R; Körük, Hasan; Choi, James J; de Comtes, FlorentinaWe demonstrated that sound can push fluid through a tissue-mimicking material. Although acousticstreaming in tissue has been proposed as a mechanism for biomedical ultrasound applications, such as neuromodu-lation and enhanced drug penetration, streaming in tissue or acoustic phantoms has not been directly observed. Wedeveloped a material that mimics the porous structure of tissue and used a dye and a video camera to track fluidmovement. When applied above an acoustic intensity threshold, a continuous focused ultrasound beam (spatialpeak time average intensity: 238 W/cm2, centre frequency: 5 MHz) was found to push the dye axially, that is, in thedirection of wave propagation and in the radial direction. Dye clearance increased with ultrasound intensity andwas modelled using an adapted version of Eckart’s acoustic streaming velocity equation. No microstructuralchanges were observed in the sonicated region when assessed using scanning electron microscopy. Our study indi-cates that acoustic streaming can occur in soft porous materials and provides a mechanistic basis for future use ofstreaming for therapeutic or diagnostic purposes.